Japan Clean Plant Co., Ltd.
Most recent update: 2025-11-01
PR message
"We are a manufacturer specializing in heat exchangers for heating and cooling air conditioners, air conditioners, drying machine, etc. For product materials, we handle stainless steel, iron, aluminum, copper, etc. at various sites.
We are also seriously working on environmental protection, energy saving equipment, waste heat utilization equipment, and clean room equipment.
We design and manufacture a wide variety of products with short delivery times and low price, from a wide variety of products to individual products.
Please feel free to contact us."
"Unit heater OA type
[Suitable place to use]
For existing general factories and warehouses
[Size (Heater only) ]
Depth 560mm x Width 440 mm x Height 650 mm 44 kg
*Other sizes are available
[Model]
SH-162-OA
*Other models are available
※[Line up]
[Steam type]
■ SH-202-OA
■ SH-242-OA
[Hot water type]
■ SH-163W-OA
■ SH-204W-OA
■ SH-244W-OA
[Cold water type]
■ SH-164W-OA
■ SH-204W-OA
■ SH-244W-OA
[Point]
It is possible to air conditioning while ventilating
☆ Due to the influence of coronavirus, the importance of ventilation is increasing day by day.
However, if the temperature inside the factory drops due to ventilation, there is a risk that the work efficiency of the workers will decrease.
Our unit heater OA type warms the air taken in as intake air, so there is no need to worry about temperature drops inside the factory! !! ☆
"
"Explosion-proof air-conditioning equipment that can be used in explosion-proof areas such as chemical plant.
If you have well water, you can countermeasure against the heat while keeping running costs down.
It also leads to energy savings and reduces electricity bills.
[Model / Size]
SC-N126E3D
Depth 820 mm x Width 740 mm x Height 690 mm
108kg
SC-N166E3D
Depth 855mm x Width 1000mm x Height 920mm
186kg
SC-N206E3D
Depth 860 mm x Width 1210 mm x Height 1040 mm
240kg
SC-N246E3D
Depth 1020 mm x Width 1460 mm x Height 1280 mm
350kg
[Point]
・ The air blowing temperature is around 25 ℃, but unlike offices, it feels cool enough as a sensible temperature in factories and warehouses.
・ Explosion-proof specifications allow safe use even in dangerous places
・ Environmentally friendly as no waste heat generated
・ Excellent dehumidifying effect
[Material]
Copper pipe x aluminum fin x Baking coating
Please feel free to contact us regarding usage, design conditions, model selection, price, etc.
We also do demonstration machine rental."
"Hot temperature inside factory due to the plating process
Bad working environment
↓
Well water type unit cooler to improve the working environment of plating factory!
If you have well water, you can countermeasure against the heat while keeping running costs down.
It also leads to energy savings and reduces electricity bills.
[Model / Size]
SC-N126E3
Depth 665 mm x Width 740 mm x Height 690 mm
96kg
SC-N166E3
Depth 680 mm x Width 1000 mm x Height 920 mm
132kg
SC-N206E3
Depth 755 mm x Width 1210 mm x Height 1040 mm
222kg
SC-N246E3
Depth 950 mm x Width 1440 mm x Height 1270 mm
325kg
[Point]
・ The air blowing temperature is around 25 ℃, but unlike offices, it feels cool enough as a sensible temperature in factories and warehouses.
・ Environmentally friendly as no waste heat generated
・ Excellent dehumidifying effect
・ As shown in the photo, it is possible to blow cold air to each worker with a duct.
[Material]
Copper pipe x aluminum fin x Baking coating
Please feel free to contact us regarding usage, design conditions, model selection, price, etc.
We also do demonstration machine rental."
"Well water type unit cooler ®
Possible to air-cooling using well water
[Significant reduction in electricity bill]
[Size]
・ Depth approx. 650 mm x Width 570 mm x Height approx. 745 mm
・ Product weight: Approx. 75 kg
[Model]
SC-D02W2
[Point]
・ No waste heat
・ With movable casters
・ Single-phase 100V method
・ Can be used simply by connecting a hose
[Material]
・ Copper pipe x aluminum fin
・ Baking coating (Munsell)
Please feel free to contact us regarding usage, design conditions, model selection, price, etc.
We also do demonstration machine rental."
"For efficient drying work!
[Suitable place of use]
Timber shop / store that handles wood
[Model / Size]
SH-162H
・ Depth 650 mm x Width 560 mm x Height 650 mm
・ Product weight 48 kg
SH-203H
・ Depth 700 mm x Width 690 mm x Height 780 mm
・ Product weight 98 kg
SH-243H
・ Depth 780 mm x Width 790 mm x Height 880 mm
・ Product weight 130 kg
*Other sizes are available
※[Line up]
■ SH-162H / 163H
■ SH-202H / 203H
■ SH-242H / 243H
[Point]
・ Can be used for various purposes and products with a blowing temperature of around 100℃. Please use it to improve the efficiency and rationalization of drying work.
・ If work such as disinfection, cleaning, and painting is also required in addition to drying timber, plastic products, rubber products, etc., install a unit heater outside the work place. Just by connecting ducts, it can be dried efficiently and cleanly without moving the products after each work.
[Material]
Steel pipe x aluminum fin, baking finish (Munsell), maximum pressure 0.8MPa, heat resistant motor method
Please contact us regarding usage, design conditions, model selection, price, etc."
"Aerofin heater (made of iron)
It is a heater that use an aerofin tube with a thin iron plate wrapped around a steel pipe. It is extremely strong and has excellent durability, and it is effective when there is a large amount of air or when the wind speed is high.
Please feel free to contact us regarding usage, design conditions, prices, etc."
"Unit heater for drying room
[Suitable place of use]
・ Ski resort (indoor drying)
・ Factory (conveyor drying)
・ Timber shop (circulation drying)
[Size]
・ Depth 700 mm x Width 690 mm x Height 780 mm
・ Product weight 98 kg
*Other sizes are available
[Model]
SH-203H
*Other models are available
※[Line up]
■ SH-162H / 163H
■ SH-202H / 203H
■ SH-242H / 243H
[Point]
Efficiently supports various drying operations!
Even if it is not a large-scale new equipment, if you have a space boiler, you can easily turn it into a drying room.
You can easily move it using a pressure resistant hose!
[Material]
・ Copper pipe x aluminum fin
・ Baking coating (Munsell)
Please feel free to contact us regarding usage, design conditions, model selection, price, etc."
"Well water type unit cooler ®
Possible to air-cooling using well water
[Suitable place to use]
Cleaning factories, high-temperature workshops, existing general factories, and warehouses
[Size]
Depth 950 mm x Width 1400 mm x Height 1280 mm
325 kg
*Other sizes are available
[Model]
SC-N246E3
*Other models are available
※[Line up]
■ SC-N126E3
■ SC-N166E3
■ SC-N206E3
[Point]
・ The air blowing temperature is around 25 ℃, but unlike offices, it feels cool enough as a sensible temperature in factories and warehouses.
・ Only the power of the fan motor, the cooling heat source does not cost
Utility model Registration No. 3214245
[Material]
・ Copper pipe x aluminum fin
・ Baking coating (Munsell)
Please feel free to contact us regarding usage, design conditions, model selection, price, etc.
We also do demonstration machine rental."
 |
Energy-saving machinery designing（ Designing / Industrial equipment designing ） |
|---|
| Company name | Japan Clean Plant Co., Ltd. | Website URL | |
|---|---|---|---|
| Street address |
Matsudo City Chiba Japan
[See map] |
Person in charge | Tsugumi Ebihara |
| Telephone number | +81-47-303-2001 | Fax number | +81-47-303-2002 |
| Capital | 95,000,000 JPY | Employees | 35 |
| Annual sales | 420,000,000 JPY | EMIDAS Member Number | 92334 |
| Main 3 products |
|
||
| Large | Medium | Small |
|---|---|---|
| Designing | Industrial equipment designing | Industrial machinery designing Energy-saving machinery designing |
| Development and production of prototype/Small-scale production | Sheet-metal processing | Pipe machining Can manufacturing Air-conditioning equipment manufacturing Chassis manufacturing Sheet metal protocol manufacturing Deburring 3-roll bending Bending (servo) |
| Development and production of prototype/Small-scale production | Blank cutting | Turret punch press processing Shearing Cutting Thin plate (below 6 mm) Stainless steel Copper/Aluminum |
| Development and production of prototype/Small-scale production | Welding/Adhesive bonding | CO2 welding Spot welding TIG welding (argon welding) Arc welding Robot welding Brazing |
| Surface treatment | Coating | Air-spray coating Electrostatic coating |
| Surface treatment | Polishing/Lapping | Buffing |
| Product manufacturing | Production property | Other industrial machinery manufacturing Energy-saving equipment/Automatic instrument manufacturing Environmental equipment manufacturing |
